Job Description

:

About Technip Energies

At Technip Energies, we believe in a better tomorrow, and we believe we can make tomorrow better. With approximately 15,000 talented women and men, we are a global and leading engineering and technology company, with a clear vision to accelerate the energy transition. Designing and delivering added value energy solutions is what we do.

If you share our determination to drive the transition to a low-carbon future, then this could be the job for you. We are currently seeking Piping Engineer (Stress) to join our team based in Kuala Lumpur, Malaysia.

Successful candidates would be offered a fixed term of employment.

About The Job

They will report directly to the Piping Stress Lead (on Projects he/she is assigned to) for all stress activities on a project for all tasks pertaining to adequacy of pipe stress and flexibility analysis, and related piping design activities, and administration matters.

Their responsibilities shall include the following but not limited to:

• Prepare the Job Specification for Stress Analysis.
• Prepare list of critical lines.
• Prepare Stress Calculation Notes.
• Liaise with Piping Designer on matters of pipe routing to achieve the requirements of a satisfactory pipe stress analysis. This may include recommendation on position and selection of various support types (anchors, guides, springs, sliding plates, etc.) for acceptable stress levels and satisfactory support loads.
• Ensure that all piping systems are adequately supported and where necessary; specify spring, sliding plates and other special pipe supports.
• Advise his Lead, should there be a need of expansion joints, bellows and other similar special units.
• Liaise with Mechanical Engineers for all matters concerning nozzle loads on equipment.
• Prepare specification, data sheets, material requisitions, technical bid evaluations/tabulations for the supply of Vendor-supplied special support items like spring supports, rigid struts, sliding plates, etc. and other special units like bellows an expansion joints.
• Review the support types and location indicated on the IFC isometric in accordance with approved stress isometrics.

Job Main Challenges

• Conversant with relevant International Codes & Standards.
• Piping analysis for Code compliance (ASME B31.3, ASME B31.8, ASME B31.4).
• Rotating equipment (compressor, turbine, pumps) nozzle load evaluation due to connected piping.
• Pressure vessles and storage tanks nozzle load evaluation due to connected piping.
• Flange joint leakage/stress evaluation.
• Spring support selection/specification, and trunnion calculations.
• Well head piping analysis considering wellhead growth(s).
• Bridge piping analysis considering relative bridge/platform displacements.

Main Accountabilities

• Prepare list of critical lines.
• Prepare Stress Calculation Notes.
• Perform selection of pipe support types.
• Ensure that all piping systems are adequately supported and where necessary, specify spring sliding plates and other special pipe supports.
• Liaise with and/or advise the Piping Designer of the pipe routing to achieve the requirements of a satisfactory pipe stress analysis.
• Prepare pipe support loading sheets for Civil/Structural design.
• Prepare specifications, data sheets, material requisitions, technical bid evaluations/tabulations
• Liaise with Mechanical Engineers for all matters concerning nozzle loads on equipment.

About You

Must have:

• Recognized Degree in Mechanical Engineering
• At least 7 years of working experience in Oil & Gas and Petrochemical field in an engineering company as piping stress analysis and support engineer.
• Experience in piping stress analysis using CAESAR II.
• Experience in manual calculation methods, and the use of nomographs and tables for assessing adequate piping flexibility.
• Experience in piping engineering including pipe wall thickness calculations, branch connection reinforcement check, pipe supports check/selection and equipment nozzle load calculations/evaluation.
• Able to assess pipe routings with regards to stress and supports.
• Knowledgeable in Industry Piping Codes and Standards, and familiar with Industry Equipment codes.
• Conversant with PI&D and its requirements.
• Fluent in English (written and spoken).
• Ability to Work under Minimum Supervision.
• Organized, methodical and detail-oriented
• A good team-worker, with a strong work ethics.
• Pro-active and willing to take initiative.
• Strong multi-tasking, problem-solving and critical thinking skills.

Nice to have:

• Able to navigate the 3D model review tools (Navisworks, Smart Plant and etc.).
• Working experience in brownfield projects.
• Previous exposure on piping design and piping layout.
• Experience with FEA tools such as Nozzle Pro, FE Pipe or others is preferred.
• Good in Excel Macros and VBA is preferred.

What\'s next?

Starting Date: Immediate

Once receiving your application, a recruiter performs an initial check and a review is further carried by hiring manager. We expect to take up to a few weeks to perform that review. If you hear from us, it is because we want to organize interviews and meet with you physically, or virtually, depending upon the location. To get an overview of the recruitment process, visit our dedicated webpage here.

We invite you to get to know more about our company by visiting and follow us on LinkedIn , Instagram for company updates.

#LI-MK1

#LI-DNI

Technip Energies